| 1. | Final temperature firing temperature
最终焙烧温度 |
| 2. | Type a 3a fuse not break for testing 90 minutes at fire temperature of 1000
A类火焰温度1000试验90分钟3a保险丝不断 |
| 3. | Available with a range of firing temperatures , to suit specific part process conditions
烧结温度范围广,适合玻璃不同方式的加工条件 |
| 4. | Color results will vary according to glaze composition , firing temperature and kiln atmosphere
唯基础釉的组成物料、窑烧温度、烧氧化或还原均会影响烧成的颜色。 |
| 5. | To analysis combustor structure ’ s contribution to fluxion and combustion explicitly , it is necessary to study the impaction of wave system and fire temperature on chemical reaction and heat release ’ s procedure
为了细致分析燃烧室结构和流动进口参数对超燃的作用关系,必须细化研究超音速流场的波系结构和燃气温度对化学反应放热过程的影响。 |
| 6. | The range of firing temperature of ceramic tube after dipping changed from 450 c to 1000 c . the above four slurries were also respectively favorable combination with al2o3 ceramic tube , and the range of firing temperature of ceramic tube after dipping slurry varied from 1 000 c to 1400 c
镀膜的陶瓷管烧成温度范围为450 1000 。前述的四种料浆也能良好地与al _ 2o _ 3陶瓷管结合，涂覆料浆的al _ 2o _ 3陶瓷管烧成温度为1000 1400 。 |
| 7. | The firing time is about 24 hours and the firing temperature is at about 1300c . lighting fireis after finishing the laying bricks for building the kiln entrance . the fuel is pine firewood . the kiln keeper , as a technical director is watching the degree of firing and controlling the change of thekiln temperature and determining the time of stopping fire
烧窑时间过程约一昼夜，温度在1300度左右。先砌窑门，点火烧窑，燃料是松柴，把椿工技术指导，测看火候，掌握窑温变化，决定停火时间。 |
| 8. | In the calculations of ultimate bearing capacity , the section of rc beam was divided into the elastic zone and the plastic zone based on the fire temperature field of the beam ' s section , the equivalent - floor - live - load was presented to describe the weakening of the bearing capacity of structure members in fire , the correlation expressions were established
摘要根据梁截面火灾温度场，将梁截面混凝土分为弹性区和塑性区2部分计算火灾场梁极限承载力，并采用等效楼面活荷载描述火灾场高温对梁极限承载力的削弱，推导了相关的计算公式。 |
| 9. | Results show that : ( 1 ) for each particle size of andalusite , variation tendency of the properties of the material is generally the same : the maximum of bulk density , compressive strength and rupture strength appears in the range of 5 % - 10 % content of fiber , these properties of the material remarkably decrease as the fiber content exceed 10 % ; while at the same fiber content , the properties of the material increase with the increase of firing temperature
结果表明： ( 1 )对于不同粒度的原料，性能变化规律大致相同：在同一烧成温度下，体积密度、常温耐压强度、常温抗折强度在5 10之间出现峰值，加入量超过10之后材料的性能明显下降；在相同的纤维含量下，随着烧成温度的提高，试样的各项性能均有所上升。 |
| 10. | It was found that there was a close relationship between the adhesion strength of the bg coating and the surface roughness of the titanium alloy and the firing temperature . the chemical state of the elements ti and si at the coating interface varied . the chemical bond and the mechanical occluding make the bg coating form a strong adhesion with the titanium alloy
通过研究发现， bg涂层与基体的结合强度与基体表面的粗糙度以及烧成温度密切相关，涂层界面处ti元素和si元素的化学状态发生了变化， bg与基体强结合的机制为化学键和机械嵌合两种力共同作用。 |
